We recently bought a new RGB laser (1,5with ILDA connection. If we use this laser on the CM2000 board it doesn't work properly with Livepro.
Following problem appears:
It doesn't dim (I only have output when I put it to 100%, when i choose for example 65% I get nothing)
When I choose colors:
white -> I get magenta
red -> OK
blue -> OK
green -> only when 100% green
Can somebody help me? Is there something wrong with the hardware of the QM2000, or is it a setup in the software? When we use another ILDA- device (USB dongle with other software) to operate the laser it works OK, so there's nothing wrong with the ILDA connection of the laser.
ILDA pins for the laser: (copy of the lasers manual)
1: X+ : -5V to +5V
2: Y+ : -5V to +5V
3: no use
4: interlock A : connected to pin 17 inside the QM 2000
5: red + : 0 to + 2,5V
6: green + : 0 to + 2,5V
7: blue + : 0 to + 2,5V
8: no use: no use
9: no use: no use
10: no use: no use
11: no use: no use
12: not connected: no use
13: no use: no use
14: X-: +5V to -5V
15: Y-: +5V to -5V
16: no use: no use
17: interlock B: connected to pin 4 inside the QM 2000
18: red - : 0 to - 2,5V
19: green - : 0 to -2,5V
20: blue - : 0 to -2,5V
21: no use: no use
22: no use: no use
23: no use: no use
24: no use: no use
25: ground: cable shielded
Before we had a gas-laser with color-crystal connected to the live-pro, witch we could dim and color change, so maybe it is just a software setting. But I just can't find it... Sorry
Thanks in advance!
Following problem appears:
It doesn't dim (I only have output when I put it to 100%, when i choose for example 65% I get nothing)
When I choose colors:
white -> I get magenta
red -> OK
blue -> OK
green -> only when 100% green
Can somebody help me? Is there something wrong with the hardware of the QM2000, or is it a setup in the software? When we use another ILDA- device (USB dongle with other software) to operate the laser it works OK, so there's nothing wrong with the ILDA connection of the laser.
ILDA pins for the laser: (copy of the lasers manual)
1: X+ : -5V to +5V
2: Y+ : -5V to +5V
3: no use
4: interlock A : connected to pin 17 inside the QM 2000
5: red + : 0 to + 2,5V
6: green + : 0 to + 2,5V
7: blue + : 0 to + 2,5V
8: no use: no use
9: no use: no use
10: no use: no use
11: no use: no use
12: not connected: no use
13: no use: no use
14: X-: +5V to -5V
15: Y-: +5V to -5V
16: no use: no use
17: interlock B: connected to pin 4 inside the QM 2000
18: red - : 0 to - 2,5V
19: green - : 0 to -2,5V
20: blue - : 0 to -2,5V
21: no use: no use
22: no use: no use
23: no use: no use
24: no use: no use
25: ground: cable shielded
Before we had a gas-laser with color-crystal connected to the live-pro, witch we could dim and color change, so maybe it is just a software setting. But I just can't find it... Sorry
Thanks in advance!